The procedure in laser marking would refer to technique in labeling or marking materials and the work pieces with used of laser machine. There are different applications that might require assorted techniques yet the annealing, foaming, removing, staining and engraving would be the common marking ways. Every laser marking polycarbonate would have own disadvantages and advantages that would depend in materials used.
The laser marking would give one the absolute freedom on markings graphics, serial numbers and barcodes in any kind of plastic material. The laser would allow the marking of any kind of content or detail, even the small that has high definition, then guaranteeing the utmost quality and readability. The marking would resists tear and wear, contact with the acids and heat then ensuring the case that has complex data would be fully traceability over time.
Those types of beams are composed of gas system containing the mixture of the CO2 which could be stimulated electrically. Those would be best suited to processing the nonmetallic materials like most plastics then offer wavelength on micrometers. The systems would be most widely using laser kind because of relatively superior and high efficiency quality.
The fiber sources laser are the solid state mechanism which generate the beam by the means of seed laser then amplify in specially glass fibers designed that would be supplied with the energy throughout pump diodes. And offering the its wavelength, the fiber would produce the focal small diameter which results of intensity up in hundred times than higher a carbon dioxide system. It is suited ideally for the metal marking like annealing, high contrast markings in plastic and engraving.
The staining would be another process in marking that is achievable as result of chemical reaction making on materials in heated of laser beam applied. There are various color shades shall depend in compositions of materials in being stained. Example, the lighter plastic color materials could often be discolor during laser etching procedure that outcome of dark marking from soot particles.
Greater degree in exposure, the more darkly would outcome. The carbonization of the polycarbonate would be visually destroyed and would be normally high value. That mark could make in penetrate deep in material it is hard in wearing it too. The laser would mark the polycarbonate often found in machine control board and another functional device.
With the traditional manual the materials would generally be need in clamped or fixed with vacuum that waste time and might be damage work piece. There is none of counterproductive and time consuming efforts that would spend in adjusting materials along with ray engraver and the materials would not chip or warp. Those beam would be universal tool in procession various materials that include textiles, wood, glass, metals, paper and cardboard.
It should be shorter ray wavelength like five hundred thirty two or three hundred fifty five could produce in higher results of the detailed. Those short wave length beams would produce less also thermal reaction in material. It is clean procedure with the near into zero wasted like byproduct.
During ray process of engraving, ray beam that exposes material in tremendous amount on heat. That results in changing color and the contrast mark the material would burn or evaporate depending in duration on time which work piece would be exposed. Finish result would be permanent and durable as well of it being resistant outside influences like scratches or abrasion.
The laser marking would give one the absolute freedom on markings graphics, serial numbers and barcodes in any kind of plastic material. The laser would allow the marking of any kind of content or detail, even the small that has high definition, then guaranteeing the utmost quality and readability. The marking would resists tear and wear, contact with the acids and heat then ensuring the case that has complex data would be fully traceability over time.
Those types of beams are composed of gas system containing the mixture of the CO2 which could be stimulated electrically. Those would be best suited to processing the nonmetallic materials like most plastics then offer wavelength on micrometers. The systems would be most widely using laser kind because of relatively superior and high efficiency quality.
The fiber sources laser are the solid state mechanism which generate the beam by the means of seed laser then amplify in specially glass fibers designed that would be supplied with the energy throughout pump diodes. And offering the its wavelength, the fiber would produce the focal small diameter which results of intensity up in hundred times than higher a carbon dioxide system. It is suited ideally for the metal marking like annealing, high contrast markings in plastic and engraving.
The staining would be another process in marking that is achievable as result of chemical reaction making on materials in heated of laser beam applied. There are various color shades shall depend in compositions of materials in being stained. Example, the lighter plastic color materials could often be discolor during laser etching procedure that outcome of dark marking from soot particles.
Greater degree in exposure, the more darkly would outcome. The carbonization of the polycarbonate would be visually destroyed and would be normally high value. That mark could make in penetrate deep in material it is hard in wearing it too. The laser would mark the polycarbonate often found in machine control board and another functional device.
With the traditional manual the materials would generally be need in clamped or fixed with vacuum that waste time and might be damage work piece. There is none of counterproductive and time consuming efforts that would spend in adjusting materials along with ray engraver and the materials would not chip or warp. Those beam would be universal tool in procession various materials that include textiles, wood, glass, metals, paper and cardboard.
It should be shorter ray wavelength like five hundred thirty two or three hundred fifty five could produce in higher results of the detailed. Those short wave length beams would produce less also thermal reaction in material. It is clean procedure with the near into zero wasted like byproduct.
During ray process of engraving, ray beam that exposes material in tremendous amount on heat. That results in changing color and the contrast mark the material would burn or evaporate depending in duration on time which work piece would be exposed. Finish result would be permanent and durable as well of it being resistant outside influences like scratches or abrasion.
About the Author:
Learn the advantages of laser marking polycarbonate with top tips from this informative website. For guidance, see the related homepage today at http://www.plasticslasermarking.com.
No comments:
Post a Comment