In case your bathroom tiles are dirty, there is need to clean them. This also applies to any part of the house. You can either hire maintenance specialists specifically for grout restoration Sarasota FL or buy a manual that will guide you to do the job on your own. The remodeling procedure is usually simple, and one can take at most one day to complete the repair job.
The list of items required for the remodeling job includes tile plaster, a utility knife, mortar float, a putty saw, spray bottle, a sponge, rag, an old toothbrush just to mention but a few. Usually, the remodeling process takes a few hours, and one can decide to take a day off to do the job rather than spending money to hire a technician.
The first thing that you need to do is selecting the adhesive you want to use for the remodeling. You must be careful when buying the plaster because it is advisable to select a color that matches with the plaster that used in the tilework. However, if you are planning to re-paste the entire floor, make sure that the color you pick matches as closely as possible with the initial adhesive.
The next thing is to ensure that you remove any loose or damaged mortar using a plaster saw. Care should, however, be taken so that you do not cause damage to the tiles bringing about more expenses that may not have been planned for. Then, clean the seams where you have removed the mortar carefully using the spray bottle and cold water.
Use the toothbrush to scrub in between the seams and remove the plaster that you had scrubbed off with the mortar saw. Then, use the towel to wipe any remaining water or mortar and ensure that the floor is dry. Mix the adhesive carefully following the guidelines provided in the manual so as not to ruin it. Plastic cans are best for mixing as they can be disposed of later on.
After mixing the plaster, spread using the plaster float very gently. Always ensure that you have filled all the seams and that they are straight and level. If you are not sure that the seams and the tiles are on the level, you can take some measurements using the putty float so that the surface looks even.
When you finish spreading the putty, make sure you wash the parts that you are done with to prevent the putty from drying. If you leave the putty to dry on the surface, it might be a difficult task to remove it. Thus it is better to wash it off while it is still wet. Use a sponge that has been dipped in water for the cleaning.
When you have finished cleaning the floorings, leave them to dry so that you may polish them. You can polish by buffing an old towel on the places where the putty was applied so that they can become shiny. In some instances, the putty can make the tiles lose their shiny appearance thus polishing is important as it restores the luster.
The list of items required for the remodeling job includes tile plaster, a utility knife, mortar float, a putty saw, spray bottle, a sponge, rag, an old toothbrush just to mention but a few. Usually, the remodeling process takes a few hours, and one can decide to take a day off to do the job rather than spending money to hire a technician.
The first thing that you need to do is selecting the adhesive you want to use for the remodeling. You must be careful when buying the plaster because it is advisable to select a color that matches with the plaster that used in the tilework. However, if you are planning to re-paste the entire floor, make sure that the color you pick matches as closely as possible with the initial adhesive.
The next thing is to ensure that you remove any loose or damaged mortar using a plaster saw. Care should, however, be taken so that you do not cause damage to the tiles bringing about more expenses that may not have been planned for. Then, clean the seams where you have removed the mortar carefully using the spray bottle and cold water.
Use the toothbrush to scrub in between the seams and remove the plaster that you had scrubbed off with the mortar saw. Then, use the towel to wipe any remaining water or mortar and ensure that the floor is dry. Mix the adhesive carefully following the guidelines provided in the manual so as not to ruin it. Plastic cans are best for mixing as they can be disposed of later on.
After mixing the plaster, spread using the plaster float very gently. Always ensure that you have filled all the seams and that they are straight and level. If you are not sure that the seams and the tiles are on the level, you can take some measurements using the putty float so that the surface looks even.
When you finish spreading the putty, make sure you wash the parts that you are done with to prevent the putty from drying. If you leave the putty to dry on the surface, it might be a difficult task to remove it. Thus it is better to wash it off while it is still wet. Use a sponge that has been dipped in water for the cleaning.
When you have finished cleaning the floorings, leave them to dry so that you may polish them. You can polish by buffing an old towel on the places where the putty was applied so that they can become shiny. In some instances, the putty can make the tiles lose their shiny appearance thus polishing is important as it restores the luster.
About the Author:
Connect with the services for grout restoration Sarasota FL locals rely on by touring our web pages today. For more info on our shower and bath makeovers, use the links at http://www.showerandbathsarasota.com/services .
No comments:
Post a Comment